Uncategorized

How to Install the Quick-Release Push-Button Lock for the Window Guard

Attach the particular Strike Pin to your window guard

The Strike Pin (3) should be once and for all mounted on or close to the outer steel framing with the home window guard -referred to from now about as WG- quietly of the WG’s “door” opposite involving the hinge, close to the middle (the same place in which a doorknob is located on the door). It should extend facing outward from the WOHNGRUPPE toward the walls, so that it will later slip into the Locking mechanism Box tip-first any time closed.

IMPORTANT: Typically the Strike Pin should point straight as you can, ie not aiming slightly up, lower, to the still left, or to the best. The straighter its, the smoother the operation later.

The spine of the Strike Pin has posts for a 1/4″ bolt, so a common way of affixing the strike green to your WOHNGRUPPE through first fixing a 1/4″ sl? it, then screwing the Strike Pin number into that. Even now, you cannot want folks having the ability to simply unscrew the bolt coming from the outside, so it is important that an individual permanently correct it in order to the WG. This really is most often performed by spot welding the attached Affect Pin in position, although if a welder isn’t handy, in whatever way the bolt can be made unturnable works, such as working with one-way bolts.

Mount the Window Guard

Whether it isn’t currently, it’s time to mount the WOHNGRUPPE on your home window. Attach the Fasten Box (1) for the end of your current pin so of which it locks in place. If it is not going to, make sure it is definitely unlocked first simply by pushing the final of the Push Rod (2) into typically the smaller hole involving the Lock Container first. It Container will be attached to the external wall of your own building, so that you will need to install the particular WG in the position where Locking mechanism Box can be attached using the best and bottom twist holes, and can not be pryed off (such as when that sits off the edge of any window frame).

One other issue to keep inside mind is that will there will end up being an approximately 1/2″ hole drilled via your wall situated in the midsection of the Fastener Box, and the inside of the particular building, a 1 5/8″ diameter Flange will mount in order to the wall about that hole. When you put way up the WG, an individual want the Locking mechanism Box to always be nearby the window starting, but far good enough allowing for this 1/2″ hole to always be drilled throughout the wall structure, and hopefully get clear of any kind of inner wall interferences (like inside framing) for a 1 5/8″ diameter close to the hole center.

Mark your gap

With the Affect Pin attached to be able to your WG, and even the WG attached to your creating, the remaining is relatively easy!

Now we need to mark the location where the hole will become drilled through the wall so that it matches the small gap on the back again of the Secure Box. First, push the Push Fly fishing rod (2) in the Locking mechanism Box hole thus it releases from your Strike Pin, and even remove it. Location the Cardboard Fall (4) right on to the Strike Pin number, and shut down the end with a knife so the particular cardboard only barely extends beyond the Strike Pin. Close the WG doorway slowly till the group of friends of cardboard complies with the wall, then use a pen to draw the circle where it lands.

Drill

Technically a 3/8″ punch bit will end up being just right for the Push Rod to fit into, nevertheless I recommend a new 1/2″ bit, which in turn leaves more room for error, in addition to is covered way up just fine. Utilizing the circle you merely marked, drill a new hole straight by way of your building wall membrane until you infringement the other side.

At this particular point, reattach the Lock Box to the WG and keep it closed. Somebody from the within should be able to put their own eye through the fresh drilled hole and see the OVERALL small hole associated with the Lock Box. If it is partially covered, drill down out the hole right up until there are a clear way to it.

push button enclosure Attach the Lock Package

If it isn’t very already, reattach the Lock Box towards the WG and keep it closed. Tag the upper and lower holes associated with the Lock Field with your trustworthy pencil, then open up the WG in addition to drill them together with the drill bit (NOT the large one! ) that will matches the screws you’re going to use to support the Lock Box, which don’t have the kit. These types of screws should be between 1/4″ and even 3/8″, and should be about 2″ to 3″ very long.

With your a couple of holes drilled over and below your current BIG one, remove the Lock Box through the WG (you learn how by now, correct? ), place it on the wall, and mount that with your screws. Screw them within until they’re cuddle, smaller completely make tighter at this time.

Align the particular Lock Box

Slowly close the WOHNGEMEINSCHAFT women mounted Secure Box, being careful To never lock this in position. What’s that will? You say the Strike Pin isn’t lining up? Take a chill pill, Now i’m getting there.

With your hammer, smack the Lock Box sufficient to move this in the direction that needs to go. In the event that it won’t move, you screwed that in a tad too tight and will need to loosen it. Whenever it is arranged properly, you may possibly lock it within place to make certain it works. It could be unlocked, of course, by adhering the Push Pole (2) through typically the hole in the wall until it emits. Note that you may want to “fish” around for that smaller hole in the Lock Box to enhance it in almost all the way.

Whenever everything is padded up, tighten the Lock Box anchoring screws all the approach. If everything is definitely well aligned, the Push Rod should easily open the particular WG plus the WOHNGRUPPE should easily lock in place. Even after the screws are tightened, you might be in a position to employ the hammer for final adjustments.

Leave a Comment

Your email address will not be published. Required fields are marked *